spacer
4 Cycle Tech Articles
New! Animal Tech
spacer
spacer
  spacer 4 Cycle Karting | Forums | Contact 4Cycle | Premium Membership


Burris Racing
ARC Racing
G-Man
AKRA

spacer

spacer


spacer   4 Cycle Karting Forums > Categories > OHV Motors > Clone Forum
spacer 2012 AKRA Box Stock Engine Specs
User Name
Password
Register FAQ/Tech Calendar

spacer
 
Thread Tools Search this Thread
  #1  
spacer 12-07-11,, 12:21 PM
ARCkartracer spacer
www.karttrax.com
 
Join Date: 06 04
Location: www.arcracing.com
Posts: 3,433
2012 AKRA Box Stock Engine Specs

Use of these Rules and Regulations require Tracks, Clubs, Promoters or Series be sanctioned by the American Kart Racing Association. Any other use is strictly prohibited without the express written consent of the American Kart Racing Association (AKRA).
The information posted here on 4cycle.com consists only of the engine specific technical data for the specific classes listed. There is considerable important information concerning general requirements, measurement procedures, class structures and tolerances that are only supplied in the printed rule book. A failure to comply with the rule book in its entirety may result in a disqualification. It is strongly suggested that racers obtain a copy of the complete book by contacting AKRA. No ruling appeal on any disqualification will be heard by AKRA unless the Track, Club, Promoter or Series involved is sanctioned by AKRA and the individual racer involved is a member of AKRA. www.akrainc.com

These rules take effect 1/1/2012

Quote:
ENGINE SPECIFIC TECH SHEET FOR: BOX STOCK 6.5 OHV

Description: Single cylinder, 2 valve, OHV 4 cycle engine.

Combustion chamber volume: 26.5 cubic centimeter minimum, with piston at TDC,using prescribed procedure. The Liquid CC check is the official check (IF THE ENGINE FAILS THE CC LIQUID CHECK AT ANY TIME DURING THE TECH PROCEDURE IT MUST BE CALLED ILLEGAL)

Cylinder Head Requirements: Must be OEM casting only. Porting and / or grinding are not permitted. Valve seats are two angles 45 degrees valve face and 30 degrees top relief. Intake seat maximum ID .897, Exhaust seat maximum ID .862. Outside face of valve may not be below floor of combustion chamber (i.e. dont sink the valves). Stock head bolts only, must have four. Head gasket/s maybe after market, must be of stock configuration, gasket thickness is a non tech item. Depth check between the valves, front to back and side to side may not vary by more than .005 max. No copper or aluminum gaskets allowed. Any stock configuration exhaust gasket allowed no other sealer.

Block Requirements: Stock cylinder bore is 2.685 max. Stroke is 2.123 + .010 or - .005. No piston pop out allowed. Matting surface finish of block and cylinder head is a non-tech item, surfacing of both to correct gasket failure and meet cc check allowed however, no piston pop out is allowed. May use 2 side cover gaskets of stock configuration. Block must remain stock as produced. Stub for governor may be removed and hole plugged. No machining of block allowed. Welding to the block shall be for rod damage repair only and may not constitute a functional modification.

Carburetor requirements: Huayi OR RUI*ING model carb only. Carb to intake sealer is gasket only no other sealer allowed. Choke must be as supplied from factory, but may be fixed to stay in open position. Venturi .615 NO-GO. Rear carb bore .751 NO-GO. Main fuel jet .042 NO-GO. Low speed idle jet is a Non Tech item. Stock emulsion tube must be used and unaltered, .066 max ID (no pass through). Side holes in E-Tube 4 holes max in bottom section and 20 holes max in top section. Minimum E-Tube length 1.092. Throttle shaft - .115 minimum. Butterfly - .037 minimum. Aftermarket air filter adapter allowed (max length of 1.375).

Valve Train: Stock valve cover only with any stock configuration gasket, no sealer.
Factory stock rocker arms 1:1 ratio and push rods only. Stock valves only 45 degree
angle only both valves, Intake valve Max OD .982 +/- .005 and Exhaust valve Max OD .948 +/- .005, no modifications allowed. Only Box Stock valve springs. (Installed Height for valve springs .815, must be checked by using the .815 spring must go gauge with retainer seal in place on intake an exhaust valve if used.) Prescribed check procedure as follows Remove valve spring, reinstall spring retainer, insert .815 must go gauge in spring location. Gauge must go in both locations Intake and Exhaust with any allowed retainers in place, as raced, during check procedure. Max wire diameter on spring wire is .071 with a maximum tension of 10.8 lbs. at a height of .850. Lash cap on exhaust valve only. Valve stem seal allowed on Intake and Exhaust valve, maximum lip thickness of .027. Minimum thickness of Intake retainer .230, Exhaust retainer .250. BS lifters only, no modifications allowed.

Ignition system: Stock Box Stock system only and must be unaltered. Kill switch and low oil sensor may be disabled and removed. Flywheel: Box Stock flywheel only (5lbs 4oz minimum) including plastic fins. BSFW-1 steel billet flywheel allowed on 1/1/12 and mandatory on 7/1/12, same weight check as stock flywheel. No alterations of any type allowed. Timing and flywheel key is non-tech.

Piston and Rings: Must be unaltered Box Stock only. No machining of piston and rings allowed.

Connecting Rod: Stock Box Stock rod only. No machining of any type allowed. Stock rod bolts only.

Crankshaft Requirements: Stock Box Stock crankshaft required. Machining, polishing, addition of material or other alteration of crankshaft is prohibited. Stock factory timing gear mandatory and must be installed in original location. Crankshaft journal diameter is 1.180max - 1.168 min.

Camshaft Requirements: Stock camshaft cores only, ez-spin assy must remain as stock. Cam lobe base circle diameter .865" -.005/+.010 Duration check for Intake and Exhaust lobes (taken off pushrod). Intake duration of 219 degrees at .050 lift/86 degrees at .200 lift.* Exhaust duration of 222 degrees at .050 lift/97 degrees at .200 lift.* (*+/- 2 degrees for wear and gauge variances) Max Intake lift on cam .225 Min .215lift taken at the pushrod. Max Intake lift at the valve .238 Taken on valve spring retainer with zero lash. Max Exhaust lift on cam .232 Min .222 lift taken at the pushrod. Max Exhaust Lift at the valve .242 Taken on valve spring retainer with zero lash. (To achieve zero valve lash for checking running lift, preload dial indicator by .001.)

Blower Housing Assembly: pull starter must be present and remain stock. Pull starter may be rotated for a better crank angle.

Header and Muffler Requirements: Any single stage, one-piece header made from .750 OD steel tubing, with the RLV Mini B-91 Silencer installed at the end of pipe. The B-91 Silencer must be tread fitted to the pipe end. The entire exhaust pipe including the muffler is 15 max length and 10 min length. Exhaust Pipe must be double nutted or safety wired and silencer must be supported by clamped on brace to secure it in place. (No aftermarket coatings of any type are permitted.)

Fuel Tank Requirements: Floor Mounted fuel tank mandatory (stock tank must be removed). Pulse type fuel pump allowed.

Fuel Pump Requirements: Fuel pump must be pulsed from either the crank case or the valve cover. You may install a flat metal plate in the original tank location for the purpose of mounting the throttle linkage and fuel pump.

Clutches: Stamped steel drum shoe type clutches only, No machined Billet drums allowed. No disc clutches allowed.

RLV Mini 91 Silencer Requirements: Part #4117 Overall Length 5.470" minimum +/-.005" - 5.600" maximum +/-.005". Threaded Nipple .685" maximum ID (ID as Mfg. NO Grinding, Reaming, or Polishing Allowed). Rear baffle holes .1285" maximum, inner baffle holes .0965" maximum. Silencer must be utilized as produced, with no modifications or alterations permitted. Strap or brace required to silencer for support, and to insure silencer does not turn and unscrew.

Claimer Rule: You must finish the race in the box stock class to purchase the winners engine for $200 or $275 if the billet STEEL flywheel is included (minus the clutch/chain guard/throttle kit, header pipe/muffler, air filter adaptor/air filter, top plate & fuel pump).


Important Note:Any attempt to increase the RPM s of the BOX STOCK PROJECT,Stock Classes, engine(example:stronger/non stock valve springs or decreasing exhaust restriction from stock levels) is strictly prohibited. Should this be allowed or preformed will mandate the use of an aftermarket Billet style flywheel for high RPM use(Super Box).ARC currently has these parts in their product line(part #s 6618/6619)and they are approved by AKRA for use,others may become available as demand increases. Note:Under no circumstances is this type of flywheel allowed in the Box Stock (Stock Classes),Stock Flywheel ONLY. No other alterations to or from stock components are allowed


ANY corrections, additions, or changes to these rules are submitted to the rules committee and approved PRIOR to being posted here. Each edit will be documented below.

Edited on 02-07-12, at 09:10 AM.
spacer
  #2  
spacer 12-07-11,, 12:26 PM
ARCkartracer spacer
www.karttrax.com
 
Join Date: 06 04
Location: www.arcracing.com
Posts: 3,433
Re: 2012 AKRA Box Stock Engine Specs

The changes from the PRINTED 2011 AKRA book are in blue text.

Edited on 12-09-11, at 07:53 AM.
spacer
  #3  
spacer 12-16-11,, 06:36 AM
ARCkartracer spacer
www.karttrax.com
 
Join Date: 06 04
Location: www.arcracing.com
Posts: 3,433
Re: 2012 AKRA Box Stock Engine Specs

Greetings

After all of the recent phone calls and all the defacation hitting the rotary oscillator on this measurement check we are going back to a cc check only. See the final version.

Thanks,

Bill

Was:
Combustion chamber volume: 26.5 cubic centimeter minimum, with piston at TDC, using prescribed procedure. The Liquid CC check is the official check (IF THE ENGINE FAILS THE CC LIQUID CHECK AT ANY TIME DURING THE TECH PROCEDURE IT MUST BE CALLED ILLEGAL), however, only when a burette is not available the following Optional check may be used (optional check is not intended to replace or override the CC check). Optional volume check, Depth of piston(checked outside edges, across wrist pin) + head gasket thickness + depth of head measured between valves = .295 minimum.


Final Text
Combustion chamber volume: 26.5 cubic centimeter minimum, with piston at TDC,using prescribed procedure. The Liquid CC check is the official check (IF THE ENGINE FAILS THE CC LIQUID CHECK AT ANY TIME DURING THE TECH PROCEDURE IT MUST BE CALLED ILLEGAL)

POST #1 IN THIS THREAD HAS BEEN EDITED TO REFLECT THIS CHANGE
spacer
  #4  
spacer 02-07-12,, 09:13 AM
ARCkartracer spacer
www.karttrax.com
 
Join Date: 06 04
Location: www.arcracing.com
Posts: 3,433
Re: 2012 AKRA Box Stock Engine Specs

The following was originally left out of the camshaft duration specs above by mistake. It is in the printed book and the correction has been made to original post.

(*+/- 2 degrees for wear and gauge variances)
spacer
spacer

« Previous Thread | Next Thread »

Thread Tools Search this Thread
spacer Show Printable Version
spacer Email this Page
Search this Thread:

Advanced Search

spacer Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



All times are GMT -5. The time now is 05:30 PM.

Contact Us - 4 Cycle Karting Forums - Archive - Top

Powered by: vBulletin
Copyright ©2000 - 2006, Jelsoft Enterprises Ltd.
gipoco.com is neither affiliated with the authors of this page nor responsible for its contents. This is a safe-cache copy of the original web site.